Feeds:
Posts
Comments

Posts Tagged ‘maunsell’

Announced as part of their range for 2016 this time last year the SR cattle trucks (technically correctly termed as being trucks being a sub set of wagons) have arrived in the last week or so from Hornby and certainly raises the bar again for rolling stock.

Diagram 1529 ex SR Cattle Truck in BR livery

Diagram 1529 ex SR Maunsell Cattle Truck in BR livery

Hornby have produced two different diagrams of SR truck. The first is a Maunsell version to Diagram 1529. Introduced in 1930 a total of 299 cattle trucks to this diagram were built to essentially the same design as the the previous SR built trucks (Diagram 1515)  except being on a steel on a 10’6″ rather than wood underframe, that were themselves derived from an existing pre-groupling ex SECR design. The final batch of 100 cattle trucks to this Diagram were introduced in 1939.
The two versions of the Diagram 1529 cattle truck released by Hornby, both in BR livery, are as follows: R6737, with running number S53732 and R6737A, with running number S53691.

Diagram 1530 Bullied Cattle truck in SR livery

Diagram 1530 SR Bullied Cattle truck in SR livery

The second is the later Bulleid version introduced in 1947 to diagram 1530. These trucks differed in construction with the end planks being replaced by plywood, reinforced on the inside by metal (I believe, in typical SR not throwing anything away style, from the metal left over when Bulleid carriage windows were stamped out from the sides).

Dia 1530, higher view, showing the aluminium roof panels

Dia 1530, higher view, showing the aluminium roof panels

The roof boards were also aluminum sheets rather than wooden. Finally the brake gear was modified to give compensated and equalised brake forces on all brake blocks and also the handbrake was lever moved to the end of the wagon to assist when shunting as it meant the lever was less likely to get covered in  deposits from the wagon inhabitants, I will leave you to guess what I mean. Although due to their introduction date the SR livery would be thought of as being very short lived the fact that such trucks would not be repainted often they survived in this livery for a number of years, sometimes with just the SR on the sides and the ‘R’ of the ‘SR’ on the ends being removed.
The two versions released by Hornby, of the Diagram 1530 cattle truck both in SR small lettered livery, are as follows: R6735 with running number 52478 and R6735A with running number 52503.

Underframe comparisons Dia 1529 top & Dia 1530 bottom

Underframe comparisons Dia 1529 top & Dia 1530 bottom

I will pretty much let the pictures on this post do the talking as Hornby have captured these cattle trucks exceptionally well and I know they have been ably assisted by friend and Southern Coaching and Wagon stock guru Mike King. Hornby’s attention to detail shines through including all the, sometimes subtle, differences between the two Diagrams such as:  body ends, brake gear, brake handles, vacuum pipes, roof construction, tie bars (Diagram 1529 only) even down to the correct split spoked wheels (a first for Hornby I believe) on the Diagram 1529 and disc wheels on the Diagram 1530 trucks. My only one question is the colour of the floor and curb rail on the SR version as this appears to be bauxite in colour, perhaps they are trying to represent varnished wood but either way I do not think this is correct (I will be touching mine up with SR brown prior to weathering).

Hornby SR Cattle trucks Diad 1529 and Dia 1530

Hornby SR Cattle trucks Dia 1530 (L) and Dia 1529 (R)

Many have commented that the livery choice of BR livery for both the Maunsell Diagram 1529 trucks and the short lived Southern livery for both the Bulleid Diagram 1530 wagons was perhaps a little odd and it would have made more sense to either do one livery version of each or the Maunsell version being the SR livery version (with either pre or post 1936 styles possible i.e. large SR lettering or small SR lettering).

Cattle trucks Dia 1530 and Dia 1529

Hornby Cattle trucks Dia 1530 (L) and Dia 1529 (R)

Although I agree that perhaps this would have been preferable, I can also understand that the way things are manufactured these days it puts possible constraints on multiple livery variations for one given manufacturing run bar a simple change of number. I am sure that other livery variations will be announced in due course, even though I intend to back date to SR liveries, a mix of large and small lettered style, my Diagram 1529 trucks.

Overall Hornby should be commended for these two cattle trucks. I am sure many, not just those modelling the SR or BR(s), will be adding a few to their fleets.

Read Full Post »

Well the annual event that is the Warley National Model Railway show at the NEC has now been and gone and by all accounts it appears that it was a good show, not that I was able to see as much of it as I might have liked. I had a good weekend on the Hornby Magazine stand operating friend and Editor Mike Wild’s latest layout Grosvenor Square, despite it being Western Region and DCC, but I think I just about coped. I apologise to anyone whom overheard and didn’t like my complaints (usually timed to gained maximum effect depending on whom was in earshot…especially that nice Mr Pete Waterman on the stand opposite…) that all Western region locomotives look the same, it was in jest… honest!

As is becoming more usual now a number of suppliers and manufacturers time announcements, product development updates and availability of new product around the time of / during the show and this year was no exception. This post attempts to round up some of those items of interest seen at the show from a Southern perspective, although this was slightly more limited than it has been in the past.

Hornby

Like last year, Hornby used the Warley show to give a presentation on some of their plans for 2017 and make some new product announcements, including a  Hitachi IEP Bi-Mode Class 800/0, which can be found via their website on their Engine Shed Blog. The full 2017 range including all the liveries variations from existing rather than new tooling is planned to be launched in January 2017.

Hornby H Class EP

Hornby H Class EP

Further to the ex SECR H lass 0-4-4T announced in September  they have also now clarified the planned initial releases as being as follows, which differs slightly from the initial information I was given at the time:

R3538 number 308 SECR lined green.  No.308 was built at Ashford Works in June 1906, entering traffic at Slades Green and was repainted to Maunsell Dark Green in 1925, when also renumbered as A308. Moving to Gillingham in July 1931, her last shed was Tunbridge Wells West, from where she was withdrawn in December 1962.

Hornb y H Class EP rear 3/4 view

Hornb y H Class EP rear 3/4 view

R3539 number 31518 BR late crest (with Overhead Electric warning flashes) lined black and pull push fitted. No. 31518 was built in July 1909 at Ashford and entered traffic at Orpington, numbered 518, Being dual braked, 518 mainly worked Chatham section trains. In December 1923 she became A518, then 1518 in July 1931. Post Nationalisation she was renumbered 31518 and later  pull push fitted in March 1952, Withdrawal took place from Three Bridges shed in January 1964.

A further view of the Hornby H Class EP

A further view of the Hornby H Class EP

R3549 number 1324 SR Maunsell Olive Green. No.1324 was built at Ashford Works in May 1907, entering traffic as No.324 at Ashford. In 1924, based Tonbridge, she often operated services between the Eastern and Central sections of the Southern Railway. Renumbered as No.31324 under British Railways, withdrawal from Three Bridges shed occurred in July 1962.

It therefore appears that the previously advised release of the BR early emblem version will not materialise as part of the first releases.

Hornby livery samples of 21C1 and 21C3 together

Hornby livery samples of 21C1 and 21C3 together

The running samples of the new original style Bulleid Merchant Navy pacifics were on display,  the malachite green versions of 21c1 and 21C3 can be seen left, and they represent the condition that these locomotives first ran between introduction in 1941 and early 1943.

Hornby 21C1

Hornby livery sample of 21C1 note the cover for the chimney

There is one correction to be made to the livery to 21C3 which will be reflected on the production models in that the side numbers and Southern lettering on the tender will be correctly shaded in black not green. The four releases of these models are due first quarter next year (delayed from 2016) and are as follows:

Hornby livery sample of 21C3

Hornby livery sample of 21C3

R3434 – SR 4-6-2 ‘Channel Packet’ ’21C1′ Merchant Navy Class (Original Air Smoothed) in as introduced 1941 condition with widows peak

R3435 – SR 4-6-2 ‘Royal Mail’ ’21C3′ Merchant Navy Class (Original Air Smoothed) in as introduced 1941 condition with widows peak

A further view of Hornby livery sample of 21C3

A further view of Hornby livery sample of 21C3

R3436 – BR 4-6-2 ‘Clan Line’ ‘35028’ Merchant Navy Class (Original Air Smoothed) – BR Brunswick Green. early crest ,

R3382TTS- BR 4-6-2 ‘Holland-Afrika Line’ ‘35023’ Merchant Navy (Original Air Smoothed) – BR Brunswick Green, early crest with TTS Sound

Look out for a post likely to be published next week detailing the exact condition and dates applicable to all these four versions which I hope will assist those wishing to purchase the correct version for their time period or those potentially wanting to renumber to other members of the class.

Hornby also announced a brand new ‘King Arthur’ tooling!  Although this is in the form a Class 87 AC electric number 87010 ‘King Arthur’ in BR Intercity ‘Swallow’ logo, (I can now remove my tongue from my cheek!)

The SR cattle trucks announced last year have this week also arrived in the shops, once my versions arrive I will post a picture review.  Just to clear up some misunderstanding on what versions have been released in this batch, as information on some retailers websites has been inconsistent due to changes in the information originally supplied / described by Hornby, the following versions are available:

  • R6735 – late SR livery, Bulleid designed version to SR diagram 1530 as introduced in 1947
  • R6735A – late SR livery , Bulleid designed version to SR diagram 1530 as introduced in 1947
    (although it would not doubt have been a while before these ended up in BR livery)
  • R6737 – BR livery  ex SR Maunsell designed version to SR Diagram 1529
  • R6737A – BR livery ex SR Maunsell designed version to SR Diagram 1529

It is still hoped that further livery versions, perhaps the inverse of the above, will be part of the 2017 range, although it should not be beyond the skills of many to re-livery the diagram 1529 version to the SR period.

I also remind readers that the 2016 livery versions of the excellent S15 4-6-0 model have also arrived at retailers namely

  • R3411 – SR 4-6-0 ‘827’ Maunsell S15 Class, Urie style tender – Post war Bulleid black with ‘Sunshine’ lettering
  • R3412 – BR 4-6-0 ‘30842’ Maunsell S15 Class, flat sided tender – BR Black early crest
  • R3413 – BR 4-6-0 ‘30831’ Maunsell S15 Class, Urie style tender – BR Black late emblem

Peco

Following on the recent announcement of their intention to produce 00 bullhead plain track with a more prototypical sleep spacing (bearing in mind that 00 being 16.5mm gauge rather the prototypical 18.83 it is still a compromise that the majority of us modellers accept) Peco also had on display an early mock up / EP of a large radius turnout which certainly looked good. It is my understanding that the geometry will match their existing code 75 streamline turnouts.

Bachmann

No new announcements from Bachmann, as is often the case at Warley, as their 2017 range is planned to be announced on January 8th next year, slightly earlier than their usual March date.

The Ep of the Bachmann ex LBSC H2 Class Atlantic 4-4-2 picture courtesy of A York / BRM

The EP of the Bachmann ex LBSC H2 Class Atlantic 4-4-2 picture courtesy and copyright of A York / BRM

In their usual display cases at the show were a number of Engineering Prototypes of current work in progress this included the first views of the ex London, Brighton and South Coast (LBSC) Brighton H2 Class Atlantic  Engineering Prototype  as seen pictured left. The planned initial releases, although it looks like tooling will allow for future further variations, for the H2 class are as follows:

A further view of the Bachmann H2 EP. Picture courtesy and copyright M Wild / Hornby Magazine

A further view of the Bachmann H2 EP. Picture courtesy and copyright M Wild / Hornby Magazine

31-920 H2 Class Atlantic 4-4-2 No. 2426 ‘St. Alban’s Head’ in Southern Railway olive green livery

31-921 H2 Class Atlantic 4-4-2 No. 32424 ‘Beachy Head’ in BR black livery with early emblem.

Also on display were the EPs of the ex SECR Birdcage Stock that have been seen for a while now.

Trafford Model Centre (TMC)

TMC announced a number of wagon commissions, via Bachmann one of which being one of the 14 Cycle branded PMVs which were introduced in 1952, primarily for use on boat trains, being essentially a modification of ex SR Parcels and Miscellaneous Vans to incorporate hooks inside to hang cycles.

The TMC cycle branded PMV

The TMC cycle branded PMV Picture courtesy and copyright M Wild / Hornby Magazine

Numbers  so converted were 1055,1103,1208,1728, these had 60 hooks presumably for up to 30 cycles, whilst 1057, 1113, 1175, 1282, 1293, 1305, 1314, 1317, 1454, 1882 had 24 hooks each. Number 1317 in addition to the bike symbols on the outside was additionally stenciled, until 1966, for use between Ashford and Cannon Street to convey cycles by manufacturer Normans of Ashford. These vans, except numbers 1175 & 1208 withdrawn in December 1962, had all returned to the general pool by 1969. The version being issued by TMC is number S1282S correctly in BR crimson livery with yellow lettering and the white cycle stencil.

TMC have also commissioned Bachmann to produce the ex LNER /BR 22T double bolster wagon and this is at EP stage

Dapol

There were no new announcements made by Dapol at the show in either 00 or N, as they are looking to get to market all outstanding products currently under development before making any new announcements. The ex London and South Western (LSWR ) B4 0-4-0T announced back in March 2014 is still at the CAD stage. They did have on show some of the results of the alignment of the Dapol and Lionheart ranges in 0 Gauge but none of these were SR related.

Kernow Model Rail Centre

Likewise no new announcements but the Kernow Model Rail Centre has on disaply their EP samples of the PBA/JIA clay tigers, the ex LSWR Gatestock as featured last week on my post here, and also, although GWR origin, the delightful diminutive 1361 class 0-06-0T saddle tanks with all the correct detail variations that they are producing.

Heljan

Back in January this year Heljan announced their intention to release an 07 Class 0-6-0 Ruston & Hornsby Diesel Shunter numbers D2985-D2998 (TOPS numbers 07001-07014).

Heljan EP / 3D sample of their proposed Class 07 shunter (version 1). Picture courtesy and copyright A York / BRM

Heljan 3D printed sample of their proposed Class 07 shunter (version 1). Picture courtesy and copyright A York / BRM

Introduced in 1962 this class of 14 locomotives was designed specifically for use in the Southampton Docks complex on trip and shunting duties. With the decline of traffic within the docks the class was re-assigned to duties in the Eastleigh area before withdrawal and finding further work with a number of industrial companies.
Heljan advise that initially two versions will be produced reflecting ‘as-built’ condition and later modified locos with waist height air brake connections as follows:

Heljan EP / £D sample of their proposed Cl;ass 07 shunter

Heljan  3D printed sample of their proposed Class 07 shunter (version 2). Picture courtesy and copyright A York / BRM

Version 1 non-air braked

2900  D2985 BR Green
2901  D2990 BR Green
2902  D2992 BR Blue
2903  07010  BR Blue

Version 2 air-braked (extra cabinet, air receiver compartment and air pipes (high level)
2910  2993  BR Blue
2911  07005 BR Blue
2912 (07001) Peakstone yellow
2913 (07003) British Industrial Sand white

Proposed for release in 2017, Heljan had a early 3D print mock ups of this model on display.

Note: that the images of Engineering Protptypes sometimes show combinations of components that are mixed and matched and do not necessarily correctly represent the combinations for model variations announced (but can be a hint at possible future variations as well!)

Read Full Post »

Today, via their Engine Shed blog, Hornby have announced that they are to produce the ex SECR / SR Wainwright H class 0-4-4 tank as part of their 2017 range. The blog post also includes images of the first 3D Stereolithography printed samples showing the excellent progress that they have made so far. Ever since they posted a teaser picture some time ago on their Engine Shed blog and social media, taken on the roof whilst photographing and measuring the only surviving member of the class, number 1263, on the Bluebell Railway the rumours have been circulating; although I have been fortunate to know it was being worked on for some time now.

My model of H class number 1522 buit from a South Eastern Finecast white metal kit

My model of H class number 1522 buit from a South Eastern Finecast white metal kit

The first 64 of the eventual 66 members of the class were first introduced by Wainwright of the South Eastern and Chatham Railway between November 1904 and 1909. The final two members of the class were eventually built under the auspices of Maunsell in 1915! They first appeared in Wainwright’s fully lined dark green livery followed by by Maunsell’s plain dark green livery, then the wartime dull grey livery up until 1923. In Southern Railway days they were in lined olive green which gave way to Bulleid black under wartime conditions and eventually British Railways lined black.

Although in a spurious malachite green livery, this is my very early attempt at producing an H Class tank using an much cut about Wrenn R 0-6-0T as the starting point, but is one of the 15 with the flat sided bunker

Although in a spurious malachite green livery, this is my very early attempt at producing an H Class tank using an much cut about Wrenn R1 0-6-0T as the starting point, but is one of the 15 with the flat sided bunker

All but two members of the class (numbers 1264 & 1312 due to cracked frames) entered British Railways service with withdrawals taking place initially between 1951 and 1953 as a result of the spread of electrification and the remainder between 1959 and 1964.  A large number of the class were fitted with standard SR air control Pull Push gear from 1949 onwards to replace some of the aging D3, R &  R1 0-4-4 tanks. There were a number of slight differences within the class such as steam and Westinghouse braked versions, slight variations in coal and water capacities, while fifteen of the class had straight sided rather than flare topped coal bunkers.

Hornby have announced their intention to initially in 2017 to produce three versions: SECR full lined green, Southern olive green (subject to confirmation) and early emblem BR liveries; along with a fourth BR late crest variant in a train pack with two Maunsell 6xx series Pull Push coaches.
Final details and actual locomotive numbers etc will be further revealed in due course, and posted on this blog when available, however the Hornby design team have advised me that they are tooling to accommodate steam and Westinghouse braked versions, flat and flared bunker sides along with those fitted with air control pull push gear.

This will no doubt be a popular release and very useful for modellers of the Eastern and Central sections of the Southern Railway rather then the Western Section which has already recently been well catered for by Hornby with their M7, N15, S15, T9 and 700 class releases.

Read Full Post »

Further to my recent post on a number of SR / BR(s) related products that have arrived in 4mm scale this post catches up on recent 2mm releases. These are the Graham Farish Bulleid 3 coach sets and from Dapol the SR Class V Schools 4-4-0.

Dapol 

The Dapol Class V Schools calss 30926 'Repton' in 2mm scale

The Dapol  Schools class V 30926 ‘Repton’ in 2mm scale

The Dapol Schools Class V  4-4-0 was first announced back in 2012 and since then I have been assisting their development team, via Richard Webster,  with some of the finer details and variations of this locomotive class. The first versions have recently arrived with the retailers.
Dapol have included within the tooling options for the correct cab variations (as 900 to 909 had lower cab side lookouts) and also those fitted with the Lemaitre multiple jet blastpipes and larger diameter chimneys by Bulleid. When looking at the picture left of 30926 ‘Repton’ remember that it is in fact an N Gauge  model!

As I advised in my recent 4mm update postDapol have also recently  announced (05/08/16) that they have Merged with Lionheart Trains. Richard Webster of Lionheart Trains has already been working closely with Dapol on the development of new models in all scales including this 2mm scale Schools class.

Graham Farish

Graham Farish also announced in 2012 their intention to produce newly tooled Bulleid coaches in N Gauge the individual coaches arrived towards the end of 2013, They have modelled the later versions of the Bulleid coaches built post nationalisation and therefore have the deeper 15″ window vents.

Graham Farish 3 coach Bulleid set 830

Graham Farish 3 coach Bulleid set 830

Earlier this year a three coach pack, comprising of two semi open brake thirds and a seven compartment composite, hit the retailers in the shape of Graham Farish reference 374-911. They are correctly numbered (s3971s / s5848s / s3972s ) for Set 830 and also have the set numbers on the ends of both the Semi Open Brake Thirds. Set 830 was the part of a batch 830 to 837  introduced in reverse numerical order between March and July 1950 for use on the South Western Section.
Although technically not latest news as I have not featured them on this blog before and now have received one these packs I thought I would give them a mention.

Read Full Post »

Some say that Southern modellers have never had it so good. Over the last couple of months a number of SR / BR(s) related products have arrived in 4mm scale (a future post will catch with recent 2mm releases). These have included: from Hornby the Class 71, ex LSWR 0415 Adams radial tanks, ex LSWR Maunsell rebuilt 58′ non corridor stock and Dapol SR style signals. I am also pleased to start with be able to provide an update on the next Class 24 release from the Sutton’s Locomotive Works.

Sutton’s locomotive Works Class 24

In my post about the launch of the Sutton Locomotive Works (SLW) Class 24 here I highlighted not only that the BR Derby built, Type 2 diesels, Class 24s played an early role in the initial modernisation plans for the Southern Region, but also that their were some details variations among the initial members of the class.

Class 24 as D5016 with ‘Athermos’ axle boxes n the condition that it worked on the Southern Region.

Class 24 as D5016 with ‘Athermos’ axle boxes n the condition that it worked on the Southern Region.

The main differences were that ten of the initial batch of 20 locomotives D5010 to D5019 and therefore nine of those that worked on the Southern Region, were fitted with the distinctive larger but experimental ‘Athermos’ axle boxes, rather than the SKF roller type that became the standard.

Philip Sutton the man behind SLW advised me at the time of writing that tooling had been produced to this variation in the future.

A view of the SLW D5016 on non ETH fitted Bulleid stock one of the reasons why they were needed on the BR(s)

A view of the SLW D5016 on non ETH fitted Bulleid stock one of the reasons why they were needed on the BR(s)

Philip paid a visit to me on Fisherton Sarum at the Barnstaple show at the end of last month with a ‘hot of the production line’ SLW catalogue number 2403 as D5016, with the ‘Athermos’ axle boxes along with extra bodyside air intake grilles, original exhaust and front end doors in all over green livery.
It goes without saying that I took the opportunity to take a quick snap of the D5016 on the main running line of Fisherton Sarum. I can also confirm that the running quality demonstrated was as good as all the plaudits elsewhere have stated. I must congratulate Philip Sutton on his attention to detail and model design with these models.

Hornby

Hornby’s output of new models over the last few months has continued at pace and for Southern modellers we now seen recently the arrival of the Class 71 Bo-Bo electric, the Class 0415 Adams 4-4-2T Radial and within the last couple of weeks the ex LSWR 58ft Maunsell rebuilt non corridor coaching stock.

Set 45 comprising of a Dia 418 Brake Composite and and Dia 99 Brake Third

Set 45 comprising of a Dia 418 Brake Composite and a Dia 99 Brake Third

The latter coaches have been developed with the assistance of friend and Southern rolling stock guru Mike King and splendidly and exquisitely (insert any other positive adjective here) represent the 58tft stock converted in 1934/5 from ex LSWR 488ft stock to Diagram 99 and Diagram 418 Brake Third and Brake Composites respectively that made up 2 coach lav Sets 42 to 46 and also the diagram 31 all third and diagram 99 brake third that were mainly used as ‘loose’ coaches. They capture the prototypes very well including the characteristic timber weatherboard that ran the full length of each coach at floor level owing to the new standard SR underframes being slightly wider than the ex LSWR bodies.

Diagram 31 all Third

Diagram 31 all Third ‘loose’ coach

Although sold as individual coaches the Dia 99 and 418 coaches have been correctly numbered, including the central end set numbering, to make up sets 42 and 43 in unlined SR olive (as introduced) and BR crimson liveries respectively. See my original Hornby 2016 announcement post here for the relevant Hornby R numbers.

Diagram 98 Brake Third 'Loose' coach

Diagram 98 Brake Third ‘Loose’ coach

These coaches were seen on the Lyme Regis branch, so are therefore a perfect companion for the ex LSWR 0415 Adams Radial  4-4-2 tanks, but also these coaches were seen on both branch and local services on across the South Western section of the SR / BR(s).
These continue the standard set by Hornby with their recent coach releases such as the Maunsell stock. Fine details include separately applied hand rails and grab handles, a representation of the grills behind the luggage compartment doors, very well detailed bogies,  fine livery application including window smoking signs.

A close up of the end of the Dia 418 Brake composite showing the exquisite detail

A close up of the end of the Dia 418 Brake Composite showing the exquisite detail

These coaches did gain SR malachite livery followed by BR style lettering on malachite (heavily varnished so slightly darker in appearance) in addition to the unlined Olive and BR crimson so far released so Hornby have a few more livery options up their sleeve. The 2 lav sets did not make it into post BR(s) Green although it is understood that a small number of the Diagram 31 and Diagram 99 coaches did.

For those wishing to fit Kadee buckeye style couplings, I can confirm that the Kadee number 18 medium length fit nicely between the coaches, bringing the sprung buffers together and should also enable the coaches to be able to be propelled OK on 2nd radius and above trackwork.

Going head to head:  both the Class 71 and the class 0415 Adams radials are going head to head with other manufacturers with the former up against the DJModels class 71 that is yet arrive and the latter with the earlier released Adams radial from Oxford Rail.

The Hornby 0415 class Adams Radial as No 30582

The Hornby 0415 class Adams Radial as No 30582

I do not currently have a Hornby Class 71 as I have preferred to wait for the DJM version which I feel is likely to be the slightly more higher specification and detailed version, however having been able to get a close look at the Hornby pre-production samples of the Adams radial last year I decided to wait for the slightly more expensive but overall in my view more accurate (taking all the slight detail variations between the locomotives at different times in their lives), and finer Hornby version, pictured left. Mine will soon be backdated to 1946 guise as 3520 in Bulleid post war black ‘Sunshine lettering ‘ livery.

Dapol 

Dapol SR Rail Post signals

Dapol SR Rail Post signals

The Dapol working upper quadrant Southern Signals available as Rail Post (for some reason named by Dapol as ‘Ladder post’) in both Home and Distant styles and a short lattice post platform Starter (some might say dinky) have now hit the retailers.
I have had previously heard mixed reports about the reliability of the previously issued Dapol signal due to their mechanism, along with the rather odd control single pulse to change control method (which does not make it easy to know which position the signal is in from the switch). It does seem anecdotally that those signals that have been controlled by a DCC accessory decoder appear to fair better than directly via push to make switch.
It is my understanding that these release utilise the same mechanism as the previous releases.

Dapol have also announced (05/08/16) that they have Merged with Lionheart Trains that will see much of the Lionheart Trains range of 7mm 0 gauge come under the Dapol brand. Richard Webster of Lionheart Trains has been working closely, (with a little assistance from myself) with Dapol on the development of new models in all scales.

As I said in the introduction above a round up of some of the recent 2mn releases will be the subject of a future post soon, so what this space.

 

Read Full Post »

Hot of the press from my friends at the Irwell Press are four new excellent paperback books all about the Southern Big Tanks. The four books cover the London Southern Western Railway Urie G16 class 4-8-0Ts and H16 4-6-2Ts Z class and the later Maunsell Z class 0-8-0Ts and W class 2-6-4Ts. These follow in the style of their more usual hardback “The Book of Series” with historical background information about each class , their design, liveries and spheres of operation, photographs along, with particular details and photographs of each individual locomotive taken from their works records. the books are of the usual high standard of detail, information and photograph reproduction that we have come to expect from the Irwell Press at a reasonable price of £13.95 each. As they say available from all good bookstores, and probably some not so good ones too! 

Southern Big Tanks:1 G16 class

G16 Book Southern Big Tanks:2 H16 class

H16 book
Southern Big Tanks:3 Z class

Z book
Southern Big Tanks:4 W class

W book
Further information about my models of members of the four class shown above can be read on my Talking Stock posts as follows:

A post about my W class model will follow soon. In the meantime I can recommend these book to any Southern Railway historian or modeller alike.

PS have you entered my little competition yet to win a brand new Hornby R2620 Urie N15 King Arthur Class number 746 ‘ Pendragon’ in Bulleid post war malachite green livery? The closing date is this coming Thursday 28th July, full details can be found here.

 

Read Full Post »

At long last, assisted by a few days off work over the recent Easter weekend, I have finally completed a few outstanding items on the workbench. This has mainly been around renumbering, naming and weathering a few items of rolling stock so I thought I would share with you some of the locomotives that I have now finished.

I have detailed a few times on this blog my method of renumbering (see Workbench Witterings #3 here) and also weathering (such as in this post here) so I wont repeat all those details this time.

Battle of Britain Class 21C149 'Anti Aircraft Command'

Battle of Britain Class 21C149 ‘Anti Aircraft Command’ with her distinctive orange background to the emblem

First up, is a Bullied Battle Britain Class 21c149 ‘Anti Aircraft Command’ for friend and fellow post war period modeller Robin Sweet (Gwrrob on RMweb) for use on his excellent, albeit GWR,  layout ‘Brent’ based on South Brent in Devon to represent one the regular SR crew route familiarisation turns, via Dawlish to Plymouth that also took WR engines over the ex LSWR north Dartmoor route.

The other side of 21C149 the addition of the RT Models front steps and Cylinder Drain pipes certainly complete the look.

The other side of 21C149 the addition of the RT Models front steps and Cylinder Drain pipes certainly complete the look.

21C149 was in this period a Salisbury engine, so again like the N Class I have done for Rob before, again a nice link to Fisherton Sarum, but Exmouth Junction must have hijacked her for a while…
She started as a Hornby 21C159 split from one their train packs as this was in the correct condition with the original forward position of the safety valves, She gained the wedge shaped cab modification in March 1948, was named in April that year and not fully renumbered to 34049 until April 1949. In addition to the renumbering and naming using HMRS Pressfix decals and Fox Transfers etched nameplates, I also fitted front steps and cylinder drain pipes from the excellent RT Models range, Springside Models front lamps and real coal in the tender.

S15 number 829 with Urie flared topped tender

S15 number 829 with Urie flared topped tender

Secondly are two Hornby S15s,  one as number 829 from the first batch of the Maunsell S15s built in July 1927 paired with a Urie style tender and one as number 845 from the third batch of Maunsell S15s  built in October 1936 paired with a Maunsell flat sided bogie tender.

S15 number 845 with Maunsell flat sided tender

S15 number 845 with Maunsell flat sided tender

Number 829 was a Salisbury allocated engine during my 1946 to 1949 modelling period, whilst 845 was initially allocated to Feltham but in 1947 was moved to Exmouth Junction and therefore would also have regularly been seen at Salisbury.

Schools Class V 929 'Malvern'

Schools Class V number 929 ‘Malvern’

Finally for now, is Hornby Schools Class V number 929 ‘Malvern’ whose repainting and numbering was the topic of my Workbench Wittering #2 post way back in June last year! Now finally her weathering is complete. As I mentioned in that post Schools class number 929 “Malvern” was one of only seven members of the class not to regain malachite green livery after the war, but stayed in SR black until January 1949. The Schools Class V were not often seen at Salisbury in SR days but as she was a Brighton allocated engine from 1947 my excuse is that she has arrived on one of the Brighton to Plymouth services that changed locomotives at Salisbury.

That’s all for now, I will post some details of some of the other items of rolling stock that I recently completed in due course.

Read Full Post »

« Newer Posts - Older Posts »

%d bloggers like this: